Skip to the page
Compare quotes from local specialists in Sacramento
SACRAMENTO HEATING AND AC Get my quote
A furnace power switch beside a furnace closet

Service guide ยท Sacramento

Furnace reset: how to do it safely

A furnace reset can fix a one-off shutdown, but a furnace that keeps tripping has a fault. Here is what is safe to try and when to stop.

  1. Tell us about the job. One short form, about two minutes.
  2. A local specialist gets in touch. They ask a few questions and quote.
  3. It is your call. Accept a quote, or don't.

Get a price for your HVAC repair job

Fill this in and a local specialist gets back to you to quote.

So the business can look at the job and price it.

A furnace reset means restarting the furnace after it shut itself off, usually by turning the power off and on at the thermostat, the furnace switch or the breaker. Some models also have a small reset button on a safety switch. Try one reset only. If the furnace shuts down again, something is wrong, and the next step is a furnace repair visit from a local specialist. This page covers the safe steps, why furnaces trip, how to keep warm meanwhile and when to ask for quotes.

How do I reset my furnace?

Turn the thermostat to off, wait a few minutes, then turn it back to heat and set it a few degrees above room temperature. If that does nothing, switch the furnace off at its wall-mounted service switch, check the breaker for the furnace and, if it has tripped, flip it fully off and then on once.

Steps in order:

  1. Set the thermostat to heat, with a temperature above the room temperature, and replace the batteries if it has them.
  2. Check that the furnace service switch, which looks like a light switch near the unit, is on.
  3. Check the breaker panel for a tripped breaker. Reset it once.
  4. Check the filter. A clogged filter can overheat the furnace and trip a safety switch. ENERGY STAR advises checking filters once a month.
  5. Wait a few minutes and see whether the furnace starts and runs a full cycle.

Do not reset more than once. A furnace that trips again has a fault, and repeated resets only hide it.

Where is the furnace reset button?

Many modern gas furnaces have no reset button for homeowners. Controls reset by switching power off and on. Where a button exists, it is on a safety switch, and it may be behind an access panel. Your owner's manual or the label inside the furnace door shows what your model has, and a specialist can find it quickly without anyone removing panels.

Do not take panels off to look for it. Your owner's manual or the label inside the furnace door shows what your model has, and a specialist can find it quickly. Brand and model matter here, so a button location described for one furnace will not necessarily apply to yours. If the manual says there is a user reset and shows where it is, press it once and stop.

Why does a furnace need a reset?

Furnaces shut themselves off when a safety device detects a problem. The cause is often simple: a dirty filter, blocked vents, a failing blower motor, or a flame sensor that cannot confirm the burner is lit. A flame sensor is a thin rod that tells the control board the flame is present, and if it cannot, the board shuts off the gas.

More serious causes include blocked venting, ignition faults and a cracked heat exchanger. A tripped flame rollout switch is a safety shutdown, so a rollout trip is a reason to stop, not to keep resetting. If your furnace lights, runs for a few seconds and shuts off, see the furnace flame sensor guide. If it starts and stops every few minutes, see furnace short cycling. If the furnace is blowing cold air, check that the thermostat fan setting is on auto, since the fan alone moves unheated cold air through the vents.

How to heat your house when your furnace breaks?

Keep the heat you have and add safe warmth. Close doors to unused rooms, draw curtains at night, put towels along drafty door gaps, wear layers and use blankets. Use an electric space heater only if it has its own safety shut-off, and plug it straight into a wall outlet, never an extension cord.

Living room with a plug-in heater and blankets on a sofa

Never use a gas oven, a charcoal grill or a camp stove to heat the home. They can produce carbon monoxide. The CPSC advises carbon monoxide alarms on every level and outside sleeping areas, and warns against running generators inside. If an alarm sounds, go outside and call 911. Symptoms include headache, dizziness, weakness, nausea and confusion. If you feel them, get fresh air and see a doctor. Sacramento's January average low is about 39.2 F (NOAA 1991-2020 normals, Sacramento Executive Airport), and older adults and babies need a warm room. If it is urgent, see furnace repair emergency.

My gas furnace isn't heating. What can I do to troubleshoot this issue?

Start with the basics that apply to any gas furnace: thermostat set to heat, service switch on, breaker not tripped, filter clean and vents open. If your furnace shows a diagnostic light or code, note it without removing anything, and the manual or a specialist can tell you what it means.

If the furnace shows a code, lights and shuts off, or smells of gas or burning, stop. Do not bypass a safety switch or open the burner area. Give the specialist the model number from the data label and any code you saw, and they can usually tell which part to bring. If you smell gas, leave the home and call 911 from outside.

Where can I buy furnace parts online?

You can find furnace parts from online sellers, but they are model specific, and gas furnace repair is not a do-it-yourself job. A flame sensor, ignitor or control board has to match your exact model, and installing it means working around gas and electrical parts. Wrong or poorly fitted parts can create safety hazards.

Instead of ordering parts yourself, record the brand, model and serial number from the label, then ask local specialists for a quote that includes the part. C-20 is the CSLB classification for warm-air heating, ventilating and air-conditioning work. Ask each business for its license number and check it on the CSLB License Check page at cslb.ca.gov. Typical part prices are on the furnace repair cost guide.

Questions people ask

How long does furnace reset take?

A reset itself takes a few minutes: power off, wait, power on, then let the furnace run through its start-up. Give it about five minutes before deciding whether it worked. Some furnaces need a few attempts of their own ignition sequence. If it fails or shuts off again, stop resetting and ask a specialist to diagnose the cause.

What should I ask before I hire someone for furnace reset?

A reset alone should not need a visit, so ask what the specialist will do beyond it. Ask for their contractor license number, the diagnosis fee, whether it is credited if you go ahead, and the price for likely parts. Ask whether they will find why the furnace tripped. Get the price in writing before work starts.

Do I need to be home for furnace reset?

For a specialist visit, yes, or another adult you have authorised should be there. The specialist needs access to the furnace and the electrical panel and needs your approval before spending money. If you are doing the simple reset yourself, stay close to the furnace for the first cycle so you notice smells, noises or a second shutdown.

Where these facts come from

Page updated